MicroNet SP5001C Manual do Utilizador

Version 2.0 User’s Manual IP Telephony Gateway Model No.: SP5001/S http://www.micronet.info

9 1.3 Front Panels The LEDs on the front panel indicate the operational status of the Gateway. (1) Console (2) LEDs Status 1.4 Back Pane

10 1.5 Hardware Specifications These are the hardware details of SP5001/S. 1.5.1 SP5001/S LEDs Table 1. SP5001/S LEDs Descriptions LEDs Fu

11 1.5.2 Back Panel Port Ethernet Port: Ethernet port is for connecting SP5001 to network, transmit rate supports 10/100 Base-T. Ethernet con

12 12V DC Port: DC Power supply. 1.5.3 Back Panel Connections This section outlines how to connect your SP5001/S to the LAN and the WAN. I

13 Step 5. Grounding SP5001/S If you want to ground SP5001/S then connect a grounded wire to the F.G. (Frame Ground) of SP5001/S. 1.6 Addit

14 Step 3. Click whether the TCP/IP Protocol has already been installed onto your computer’s Ethernet card. Note that TCP/IP Protocol can be

15 2. Web Configuration with FXS Introduction 2.1 Accessing the Web Configuration The embedded web configuration allows you to use a web b

16 Figure 2. SP5001/S web configuration welcome screen The following table describes the screen. Table 2. Navigation Panel Links LABEL DESC

17 LABEL DESCRIPTION Flash Clean This link takes you to a screen where you can click flash memory information and configuration. Commit Data

18 3. Initial Configuration This chapter describes the procedure for the initial configuration of SP5001/S. Refer to the relevant chapters in

1 Table of Contents 1. SP5001/S OVERVIEW...

19 Figure 5. Commit Data Step 3. Click Reboot Data on the navigation panel. In the Reboot FXS System screen, click the Reboot button. It wil

20 3.3 DHCP mode Step 1. To configuration the IP address of SP5001/S for DHCP Mode, click Network Interface on the navigation panel. In the

21 3.4 IP Sharing Configuration One Sets SP5001/S The function is for user whose network environment is behind IP Sharing device. It is said

22 Please see following for example: >Advanced setting > NAT setting > DMZ Host setting DMZ Host setting Activate DMZ DMZ Host

23 Step 3. Click Commit Data on the navigation panel. In the Commit Data screen, click the Commit button. In the Commit Data screen to Displa

24 See following for example. >Advanced setting > NAT setting > Port Redirection Active Configuration Items Service name Prot

25 the DMZ Host. After the IP Sharing configuration of SP5001/S and IP Sharing device is complete, you must reboot SP5001/S to activate the ne

26 4. Making a VoIP Call This Chapter covers the basic configuration the gateway for making VoIP calls. One is the Peer-to-Peer mode, another

27 Figure 10. Phone Book Step 3. E.g. enter the Index: 1, Name: test1, IP address: 192.168.4.72 and e164: 200 of the destination and click

28 Step 4. On table will display on the first index. Figure 12. Phone Book Step 5. Click Commit Data on the navigation panel. In the Commi

2 9. VOICE SETTING SCREEN...37 10. PHONE PATTERN

29 4.2 Configure the gateway into the Proxy routed mode Step 1. To configuration the SIP Configuration of SP5001/S, click SIP Information o

30 5. Upgrade ROM Version This Chapter covers the basics of how to upgrade ROM Version. 5.1 Before you start downloading 1. Please confirm

31 Figure 15. ROM File Upgrade OK Step 3. Click Flash Clean on the navigation panel. In the Flash Clean screen, click the CLEAN button. In

32 Step 4. Click Reboot Data on the navigation panel. In the Reboot FXS System screen, click the Reboot button. It will take 40 seconds to re

33 6. Network Interface Screen Click Network Interface in the navigation panel and open the Network Interface Screen. Use this screen to setu

34 LABEL DESCRIPTION SNTP Server Address Set specify a SNTP Server as network time source in dotted decimal notation for e.g. 168.95.192.12.

35 7. SIP Information Screen Click SIP Configuration in the navigation panel and open the SIP Information Screen. Figure 18. SIP Information

36 8. System Configuration Screen Click System conf in the navigation panel and open the System Configuration Screen. Figure 19. System Conf

37 9. Voice Setting Screen This Chapter covers voice is associated with the audio setting information. Click Voice Setting in the navigation

38 LABEL DESCRIPTION Optimized Factor (Jitter): Setting Optimized Factor (Jitter). OK Click OK to save your changes back to volatile memory.

3 List of Figures Figure 1. Login Screen...

39 10. Phone Pattern Screen The progress tone of SP5001/S is configurable. Default tone value is set according to U.S. tone specification. Us

40 11. Support Function Screen Click Support Function in the navigation panel and open the Support Function Screen. Figure 22. Support Funct

41 12. Phone Book Screen This Chapter covers Phone Book function allows users to define their own numbers, which mapping to real IP address.

42 LABEL DESCRIPTION Name Set up a descriptive name. IP Address Set up IP Address or Domain Name. e164 No. Set up e164 (telephone) number

43 13. DSCP Configuration Screen This Chapter covers IP Packet ToS (type of Service)/Differentiated Service configuration. Click DSCP Configu

44 14. Password Screen Click Password in the navigation panel to open the Password Configuration screen. Use the Password Configuration to se

45 15. ROM Upgrade Screen Click ROM Upgrade in the navigation panel and open the ROM Configuration Screen. Figure 26. ROM Configuration The

46 16. Flash Clean Screen Click Flash Clean in the navigation panel and open the Flash Clean Screen. Figure 27. Flash Clean The following t

47 17. Commit Data Screen Click Commit Data in the navigation panel and open the Commit Data Screen. Figure 28. Commit Data The following t

48 18. Reboot System Screen Click Reboot System in the navigation panel and open the Reboot FXS System screen. Figure 29. Reboot FXS System

4 Figure 36. Change password Screen ...52 Figure 37. quit co

49 19. Command List This chapter introduces the command line interface and lists all of the commands. 19.1 Hyper Terminal Setting A termina

50 Step 3. After pressing OK button, the next window will appear, and then choose COM1/2 Port, which you are going to use. Figure 32. “Conne

51 19.2 Power Up Your SP5001/S At this point, you should have connected the console port, the LAN Port, the WAN port and the power port to t

52 Set Password To set your own password in root login name, just input command “passwd –set root ****”. For example, if password of root acco

53 19.3.3 Application Mode Configuration It is including Basic mode, such as Proxy Server and Peer-to-Peer, and Advanced mode, IP-Sharing m

54 command. For detail, please refer to Chapter 19.7.13 [security] command. An example is demonstrated below: usr/config$ security –line 1 –na

55 Expires:3600 Registering to: Sip:80.248.33.37 with the following : To:sip:[email protected] From:sip:sipc

56 Note: The command is to add a record onto PhoneBook. After the command completed, you can type “pbook –print” to see if the input record is

57 Fixed IP Address: usr/config$ ifaddr –ipsharing 1 210.11.22.33 Note: With Dynamic WAN IP Address, when the WAN IP is changed, we need to

58 Two Sets of SP5001/S 1. The WAN IP Address obtained from ADSL has two kinds of methods. One is fixed IP Address, while user applies for

5 List of Tables Table 1. SP5001/S LEDs Descriptions ...10 Ta

59 >Advanced setting > NAT setting > Port Redirection Active Configuration Items Service name Protocol Actual Port Virtual I

60 19.4.4 PPPoE Mode Press [?] or [help] to list all commands, including PPPoE one. Step 1. pppoe –dev 1 : switch the IP configurations

61 Enable the PPPoE function of SP5001/S Command: usr/config$ pppoe -dev 1 Save the configuration and initiate the PPPoE connection. Command:

62 B. 2MB Rom: usr/config$ rom –boot2m –s 192.168.1.1 –f 2m4asipfxs.104b Description: -app / -boot2m means the prepared upgrade Rom; -s means

63 19.6 Commands in SP5001/S The following table lists all of the commands that you can use in SP5001/S. Refer to the following chapters for

64 19.7 System Commands Overview 19.7.1 [quit] Type quit will quit configuration mode. And turn back to login prompt. usr/config$ quit Dis

65 Parameter Usages: -status Display the enabled debug flags. -add Add debug flag. -sip sip related information -msg voice related inf

66 19.7.4 [flash] Save changes after configuring SP5001/S. usr/config$ flash Flash memory information and configuration Usage: flash -clean

67 19.7.5 [commit] Save changes after configuring SP5001/S. usr/config$ commit This may take a few seconds, please wait... Commit to flas

68 Parameter Usages: -print print current IP setting and status -ip assigned IP address for SP5001/S -mask internet subnet mask -gate IP d

6 About this User’s Manual This user’s manual gives hardware specifications and explains web configuration and command line configuration for

69 19.7.7 [time] When SNTP function of SP5001/S is enabled and SNTP server can be found as well, type time command to show current network ti

70 19.7.9 [pbook] Phone Book function allows users to define their own numbers, which mapping to real IP address. It is effective only in pee

71 SP5001/S will give each record a automatic sequence number as index. -add add a new record to phone book. When adding a record, users have

72 19.7.10 [pppoe] Display PPPoE related information. usr/config$ pppoe PPPoE device information and configuration Usage: pppoe [-print]|[-o

73 19.7.11 [sysconf] This command displays system information and configurations. usr/config$ sysconf System information and configuration U

74 usr/config$ sysconf -print System information Inter-Digits time : 3 BusyForward : OFF Ke

75 19.7.12 [sip] This command is to configure SIP related parameters. usr/config$ sip SIP stack information and configuration Usage: sip [-m

76 of the registration information. -port SIP local UDP port which uses to listen incoming SIP Messages. -rtp Specify the RTP received port

77 19.7.13 [security] This command is used to configure the account information included username and password obtained from the service prov

78 19.7.14 [voice] The voice command is associated with the audio setting information. There are four voice codecs supported by SP5001/S. usr

7 1. SP5001/S Overview SP5001/S FXS Gateway which integrates data and voice in one device and is based on IETF RFC 2543 bis-09 compliance pro

79 parameter, 20/40/60ms is applicable to G.711u/a law, and G.729 codec, while 30/60ms is applicable to G.723.1 codec. -priority codec priori

80 usr/config$ voice -print Voice codec setting relate information Sending packet size : G.729A : 40 ms G

81 Note: it is not recommended to change the value in this command, only if users do know well the application. This might cause incompatibili

82 19.7.17 [phone] The progress tone of SP5001/S is configurable. Default tone value is set according to U.S. tone specification. Users may a

83 Parameter Usages: -print print current call progress tone configurations (ring: ring tone, rbt: ring back tone, bt: busy tone, dt: dial to

84 19.7.18 [rom] ROM file information and firmware upgrade function. usr/config$ rom ROM files updating commands Usage: rom [-print] [-app]

85 usr/config$ rom -print Download Method : TFTP Hardware Ver. : 3.0b Boot Rom : sdboot.200 Application Rom : 4asipfxs.106

8 Ÿ One RJ11 Telephone Port (FXS). Ÿ DC 12V input. Ÿ System Monitoring Ÿ System status (Link, Ready, Status, TEL, Power). Remote Firmware