MicroNet InTagral Plus Especificações

Magic Aire Factory Control OptionsI0M# 011-200001-003 MicroNet LONMARK® 200 Series Controllers The I/A Series MicroNet LONMARK 200 Series Contro

B) Face and Bypass Damper Actuator This non-spring return actuator is connected to 24 VAC power and is controlled with a 4-20 mA signal from Analog O

A) 2-Pipe unit (steam/water), Damper Control Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccupied) override mo

B) 2-Pipe Unit (steam/water), Valve Control Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccupied) override mod

C) 4-pipe unit (hot water or steam and chilled water), Damper Control Fan Operation The supply fan shall run continuously in the occupied and tenant

D) 4-pipe unit (hot water or steam and chilled water), Valve Control Fan Operation The supply fan shall run continuously in the occupied and tenant

E) Electric Heat Only Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccupied) override modes. The fan shall cycl

F) DX cooling only Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccupied) override modes. The fan shall cycle w

G) DX Cooling with Electric Heat Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccupied) override modes. The fan

H) DX Cooling with Wet Heat, Damper Control Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccupied) override mod

I) DX Cooling with Wet Heat, Valve Control Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccupied) override mode

Current Ratings 24 VA at 24 Vac, pilot duty. Universal Inputs 10KW Thermistor w/ 11KW Shunt Resistor -40 to 250 °F (-40 to 121 °C) range. TS-5700-85

J) Damper Controlled Chilled Water Cooling with Electric Heat Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccu

K) Valve Controlled Chilled Water Cooling with Electric Heat Fan Operation The supply fan shall run continuously in the occupied and tenant (unoccup

7) Typical Unit Wiring A) Control Diagram, 2-pipe Damper Control UI2LONUI3AO2DI2DI1S-LKAO1COMS-LKLONUI1COMCOMCOMGNDNO6NO1C2C4C5NO5C3NO4C624HNO3C124

B) Control Diagram, 2-pipe Valve Control C) 1: Timeclock, Day/Night Relay & Pneu. SW Contacts are: OPEN for Occupied Mode

C) Control Diagram, 4-pipe, Damper Control NOTESFB ACTUATOR1: Time Clock and Day/Night Relay Contacts are: OPEN for Occupied Mode CL

D) Control Diagram, 4-pipe, Valve Control Y2Y1GG0UI2LONUI3AO2DI2DI1S-LKAO1COMS-LKLONUI1COMCOMCOMGNDNO6NO1C2C4C5NO5C3NO4C624HNO3C124GNO2MN 200I/A S

E) Control Diagram, DX with Electric Heat UI2LONUI3AO2DI2DI1S-LKAO1COMS-LKLONUI1COMCOMCOMGNDNO6NO1C2C4C5NO5C3NO4C624HNO3C124GNO2MN 200I/A SERIESRR

F) Typical Power Diagrams SW2SW1FU1115/265 VL1NGNDDISC1TRAN3SEE UNIT WIRING DIAGRAMFOR TRAN3 WIRING DETAIL.24VACTRAN13 1FR1FR124CBC1132SEE CONTR

8) Parts List A) Standard Control Parts UI2LONUI3AO2DI2DI1S-LKAO1COMS-LKLONUI1COMCOMCOMGNDNO6NO1C2C4C5NO5C3NO4C624HNO3C124GNO2MN 200I/A SERIESRPGM:

9) Troubleshooting Chart Symptom Check Explanation Unit in Occupied Mode? Fan runs continuously in Occupied and Tenant Override Modes. Unit in Unoc

1) Dual-Mount Thermostat (Wall Thermostat) ... 2 A) Use ...

1) Dual-Mount Thermostat (Wall Thermostat) A) Use The dual-mount thermostat or "wall 'stat" is factory mounted in the unit for setpoin

E) Remote Mounting (Wall Mounting) The dual-mount thermostat is factory mounted on the control panel. This thermostat may be mounted in the space fo

123450.31"1.50"2.69"0.70"1.91"3.08"3.95"Figure 2 - Subbase Mounting Holes & Dimensions F) Thermostat Accessori

C) Measurement & Scale At least one of the sensor wires must be disconnected from the controller before resistance measurements are taken. A dig

(4) The outdoor air damper position returns the percentage of full-scale output (20mA) being sent through the proportionally controlled actuator. Unl

D) Controller Lights (LEDs) The controller is equipped with 3 LEDs that are green (closest to edge of controller), yellow, and red (closest to center