MicroNet SP5018 Manual do Utilizador

User’s Manual IP Telephony Gateway Model No.: SP5108A, SP5058A, SP5008A, SP5208

9-----------------------------------------------------------------------------------------

103. Startup First of all, connect your computer to Micronet SP50X8A’s LAN port by using D

11 2. You will enter the main page of the web configuration interface after you keyed in

12

13 3.2 Network Configuration The following instructions will explain the configurations f

14

15WAN Setting Item Description Static IP DHCP PPPoE Connected mode Select the connection

16http: http access only https: https access only both: http and https access are allowed

17WAN Setting Item Description Static IP DHCP PPPoE Default gateway Specify the IP addre

183.2.1.1 WAN Setting --Static IP 1. Press the “Apply” button (at the bottom) after you

1 1. Introduction ...

193.2.1.2 WAN Setting --DHCP 1. Press the “Apply” button (at the bottom) after you finis

203.2.1.3 WAN Setting --PPPoE 1. Input PPPoE user ID and password 2. Press the “Apply” b

213.2.2. LAN Setting LAN Setting ITEM Description LAN Mode It supports Bridge or NAT mo

22LAN Setting ITEM Description Domain Name You can specify the domain name that will be

233.3 General configuration To make VoIP calls, you will need a SIP account provided by th

24 PABX Connection To enable PABX behavior or not. SIP Setting Please refer to 3.3.2.1

253.3.2 SIP Setting Proxy Redundant Mode Disable: only register to primary proxy. Act-A

26truing. Primary proxy Specify the data of primary proxy: Enable/Disable, IP address,

27Ring Type Select the Ring Type of representative number. You can choose the following:

28 3.3.3 SIP Advanced Setting Local SIP port(1~65535) Specify the local starting SIP

23.4.8 Dial Plan...

29proxy. Min Session Expire(Sec) Specify the minimum session expire time that other host

30this feature. When enable it, you can hide your VOIP traffic from ISP’s monitor. SIP ses

31 3.3.4 Payload Type Setting RFC2833 payload type Specify the RFC2833 payload type (ra

32 3.3.5 Line Setting

33 No Answer Forward Time (FXS only) If you enable the No Answer Forward function (sip t

34proxy. The default setting is 1000~1007. Enable Hotline Click the check box to enable h

35 3.3.6 Qos Setting Type Select Qos Type: DSCP or ToS Differentiated Services Code Po

36network environment. 1. Press the “Apply” button (at the bottom) after you finish to sa

373.3.7 Speed Dial Setting Speed Dial Editor Specify the speed Dial Number/Telephone Nu

383.3.8 Caller ID Setting Caller ID Setting (Line 1~Line 8) Select the (Line 1~Line 8)C

3 1. Introduction 1.1 VoIP Gateway Micronet SP5008A / SP5018A / SP5058A are high-capacity

39The “Disable” option will allow you to disable this particular function. DTMF Caller ID

403.3.9 CDR Setting CDR mode Select the CDR mode for Enable or Disable. If you Enable thi

41P.S. To receive the SYSLOG CDR, you need to have a syslogd server to collect the CDR fro

42 3.3.10 Syslog Setting This syslog is used to send the debug log from Micronet SP50X8A t

43 P.S: To receive the SYSLOG debug information, you need to have a syslogd server to col

443.4 Advanced Configuration 3.4.1 System setting prack PRACK is defined in RFC 3262: R

45T.38 NoAttribute No attribute (Fax version, Bit Rate, Buffer, Datagram…) indicated in T

46limitation range is 1~5sec. FAXByPass Keyword Some SIP Proxy need specify special keywo

47z Polarity Reversal When enable the Polarity Reversal Detection, SP50X8A (FXO) will use

48voice. 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2

4z Support detection of disconnect tone, polarity reversal, and loop current drop (zero v

493.4.2 SNTP Setting SNTP mode Select the SNTP mode : On or Off SNTP server address Sp

503.4.3 Codec Setting Codec Priority Selection order to match the remote SDP for codec

51G711A 20,40,60 G723 30,60,90 G729A 20,40,60 G726 20,40,60 Bandwidth Required When you

523.4.4 Voice Setting Jitter Buffer Minimal Delay Specify the minimal delay of the jitt

53Remote receive volume Specify the volume gain of the voice in the remote side (+5~-20 d

543.4.5 Tone Setting Dial tone Specify the pattern of the Dial tone, you can adjust th

55 P.S. If the disconnect tone only has single frequency, please set it to low frequency.

563.4.6 Phone Setting Primary Ringing Ringing Frequency Specify the Ringing frequency

57If the phone-set’s flash time is larger than the Flash high setting, the flash will be h

583.4.7 Digit Manipulation Digit Manipulation Editor z FXO: This DM group is used for FX

5QoS – 802.1Q Virtual LANs DiffServ (RFC 2475) / ToS (RFC 791/1349) z IP Telephony (VoIP)

59replace value. It might be useful, if you want to wait for a while and dial the second p

603.4.8 Dial Plan Dial Plan Editor Using this feature, users can specify the number tha

61z Total digit count: 8 If the user dials an 8 digit number (e.g. 82265699), the MICRONE

623.4.9 Call routing Editor Call Routing z Status: enable or disable this routing z Pr

633.5 Management 3.5.1 Provision Server The Micronet can support the EMS9510 or http provi

64 Provision server Mode HTTP: Enable auto provisioning service by HTTP Service Provisi

65 Provision server Mode FTP Provision server IP address Specify the Provision Server’

66 3.5.2 Save-Reload setting Export File Click the “Export” button to export “user.cfg”

67 3.5.3 Voice File Voice File Type Voice files type to be uploaded. It could be greeti

683.5.4 Upgrade Firmware Http Upload Specify the location of the firmware for uploading

6Adjustable volume level z Security HTTP 1.1 basic/digest authentication for WEB access

693.5.5 Reset to Default Users can restore back to factory default settings using this fe

703.5.6 Network Status Connection mode Displays the current connection mode. Current IP

713.5.7 Version Info. Boot version Displays the current boot version loaded on the MICR

723.5.8 Port Status Refresh Interval Time to update the status Item Displays the corres

73 3.5.9 Account Three level of users can be used, administrator, supervisor, user. Each

74 3.6 Rebooting the system Executing this function will reboot the whole system, when c

75Appendix A: How to set the P2P call Example1: This example shows a way to do the P2P i

76 Step 2: Disable Register for all line and apply it.

77Step 3: Create a prefix as follow to route the call to SP5058A as follows. Reboot and tr

78B. SP5058A configuration Step 1: Disable proxy settings as below and apply it.

72. Physical Description 2.1 Front Panel: LED Indicators SP5008A: SP5008A Front Pane

79Step 2: Disable register for all lines as follows and apply it.

80Step 3: Create prefix to route to SP5008A’s FXS port. Reboot and try it. For this exampl

81Example 2: This configuration shows an example to use the hot line for p2p calling. It i

82Step 2: For the line need to do the P2P hot line, put hotline number as the format of “n

83B. SP5058A configuration Step 1: Disable proxy settings and apply it.

84Step 2: For the line need to do the P2P hot line, put hotline number as the format of “n

85Example 3 This configuration shows an example for P2P calling to a representative number

86Step 2: Disable SIP registers for all lines and apply it.

87Step 3: Create a call routing entry for routing to SP5058A’s representative number as be

88B. SP5058A Configuration Step 1: Check the primary proxy and representative number enab

8WAN Blink / Green Transmitting or receiving data /Network connection established LAN(1-

89 Step 2: Disable sip register for all lines and apply it.

90Step 3: Create a call routing entry for routing to SP5008A’s representative number as be