MicroNet SP3508A Guia de Instalação descarregar pdf

P/N 2300-0504

Quick Installation Guide

8-Port VDSL Managed Switch

Model No.: SP3508A

Installation

Connecting to Gigabit Ethernet

The VDSL Switch has 2 x 10/100/1000 Mbps Gigabit Ethernet

ports.

Support full or half-duplex operation and transmission mode is

using auto-negotiation.

All network devices connected to the switch must support

auto-negotiation. Devices without auto-negotiation will operate

at half-duplex.

Upgrade devices to support auto-negotiation and auto-

crossover (MDI/MDIX) for full-duplex operation.

Prepare straight through shielded or unshielded twisted-pair

cables with RJ-45 plugs on both ends. Use 100 Category 5

cable for connections.

When inserting an RJ-45 plug, be sure the tab on the plug

clicks into position to ensure that it is properly seated.

Connect one end of the cable to port 9 or 10 of the VDSL

Switch, and the other end to a standard RJ-45 station port on

cable modem, ADSL router, wireless bridge, etc.

Do not plug a RJ-11 phone jack connector into the Ethernet

port (RJ-45 port). This may damage the VDSL. Instead, use

only twisted-pair cables with RJ-45 connectors that are

compliant with the FCC standards

•

Connecting to RJ-11

Please ensure suitable VDSL Modem (SP3501AS) is

installed before making a connection to any of the VDSL

Switch (1-8) station ports. Users need to prepare 18 ~ 26

gauge one twist pair phone Line wiring with RJ-11 plugs at

both ends.

The Modem's RJ-11 ports are easy-to-use and do not require

installation of additional wiring. Every RJ-11 modular phone

jack in the home can become a port on the LAN.

Networking devices can be installed on a single telephone

wire that can span up to maximum of 1.7km between the two

points.

SP3508A has embedded Splitter between every VDSL side

(VDSL Line) and POTS side (POTS port). It permits user to

deliver broadband service on the same lines as Plain Old

Telephone Service (POTS), PBX, ISDN traffic and VDSL

Signal.

•

• When inserting a RJ-11 plug, be sure the tab on the plug

clicks into position to ensure that it is properly seated.

Web-based User Interface

SP3508A is embedded with web-based

UI and provides a series of web pages,

which display the configuration and status of the system. After

configuration of IP, the management interface can be access by

entering the IP address of the switch into the browser.

•

IP Address

Subnet Mask

Username

Password

192.168.16.250

255.255.255.0

admin

123

IP Address Configuration

PC/Notebook must belong in the same IP range and subnet.

Follow the steps below to configure IP settings for LAN PC.

Step 1.

In the control panel, double click on

Network Connections. Double click

on the local area connection (e.g.

LAN). The following screen will

appear. Highlight 'Internet Protocol

(TCP/IP)' and click on 'Properties'.

Step 2.

Enter the IP address

192.168.16.x and subnet mask

255.255.255.0 then click <OK>.

P/N: 2300-0504

Web: www.micronet.com.tw

1 2

Resumo do Conteúdo

Página 1 - 8-Port VDSL Managed Switch

65P/N 2300-0504Quick Installation Guide8-Port VDSL Managed SwitchModel No.: SP3508AInstallationConnecting to Gigabit EthernetThe VDSL Switch has 2 x 1

Página 2 - Physical Description

431 2IntroductionMicronet SP3508A is an EoVDSL (Ethernet over VDSL) clustering switch that aggregates 8 VDSL lines into 2 Gigabit Ethernet uplinks. It